Make your own free website on Tripod.com

Magnetic Resonance Amplifier

Description of Operation

By Joels McClain,


The MRA is a series resonant LC circuit in which power gain is attainable as a result of the increase in effective impedance under certain operating conditions. When the series impedance increases, primary current is reduced. When the power available from the secondary coil either remains the same or increases as the primary circuit impedance increases, a power gain occurs.

This is not possible with a series resonant circuit made of conventional materials. Even unity power transfer is considered to be unattainable as a result of accumulated losses in the components which are passive (reactive) devices. Materials and construction methods are chosen for these components based upon the type of application and frequency to be applied, with the goal of minimising losses.

A typical capacitor with polyethylene dielectric has a dielectric constant of 2.3 times that of air. Air has a constant of 1.0, and is the basis for comparison. Titanium dioxide, however, has a dielectric constant maximum of 170, and a corresponding power factor of only 0.0006, comparable with polyethylene, so that the dissipation of primary current in the dielectric is extremely low. This is where the comparison ends, because the titanium composite "capacitor" is also a piezoelectric device as well as an excellent capacitor.

Heat adversely affects the power factor of most dielectric materials. Titanium zirconate, however, contains polar molecules which rotate as thermal pressure is applied. This rotation increases the dielectric constant if the frequency applied is equal to or lower than the resonant frequency of the dielectric.

At series resonance, the rotation of polar molecules contributes to heat; as the dielectric constant increases, a corresponding release of free electrons occurs as a direct result of the piezoelectric properties of the device.

In application, the MRA is tuned at resonance for maximum power transfer, then detuned slightly for maximum power gain. This relates directly to the use of thermal pressure at resonance, and the effect that this has on continued polar rotation and the release of donor electrons.

The coil or primary of the MRA is a magnetic core which, relative to the fixed capacitance of the piezo, is a tuned permeability device. This is often used in RF devices to attain a stable resonant frequency. Magnetic materials are chosen based upon the operating characteristics of the intended application to reduce eddy currents in the operating range.

In these applications, the resonant frequency of the magnet itself is avoided, as this would "beat" with the oscillating current. However, in the MRA, this is the exact effect we want.

The barium ferrite magnet resonates audibly at frequencies which are harmonics of the series resonant frequency. The effect of this in a typical audio application is called harmonic distortion and is not desirable, but, once again, in the MRA this what we want to occur.

There is energy in the harmonics, and this energy serves both to counter eddy losses as well as to oppose primary current flow, while contributing to circulating current within the resonant circuit.

The net effect of this is that when the MRA is detuned, harmonics of the audible frequency "beat" with primary current, opposing its flow, while the increase in circulating current couples more power to the secondary, and therefore to the load. This is how the power gain is attained, basically by considering the naturally occuring harmonics as beneficial instead of as undesirable effects to be filtered out.

When the MRA is detuned, the effective impedance increases as seen by the source, while the power available to the load decreases in lesser proportion. This is measurable by using resistive equivalent circuit testing. However, the detuning is load-dependent, and slight adjustments are required if the load requirement is greater than the power band of a harmonic interaction.

After retuning, the power to the load will increase in quantum intervals as the circulating current is reinforced by the reaction of the permeable magnet core. This will be seen as slight incremental voltage increases across the load device.

Once the magnet is "ringing", its frequency and therefore harmonics remain stable as long as the series resonant range is not exceeded. Therefore, the detuning affects the piezo only, and the circulating current increase is a result of the phase relationship between the harmonic and the source.

Voltage amplification is seen across the primary, measurably higher than the source voltage, and this is "seen" by the secondary. This is not the same thing as a power gain, because the the power gain is a direct result of the effective impedance.

It should also be noted that the term "virtual rotation" has been applied in describing the operation of the MRA. The comparison is made with a generator, in which relative motion occurs between a coil and a magnet. Rather than use physical energy to rotate a mass, the MRA uses resonance to rotate the energy.

This is seen in the polar rotation of the piezo dielectric as well as in the molecular energy occuring in the reactive component of the magnet, i.e. the ringing. The lattice structures of the piezo and magnet are compatible for virtual rotation, and the materials complement each other electrically.

In the past, researchers have noted many effects which occur at aggregrate resonance which typically includes a range of three octaves. Anomalous energy gains were referred to as "aetheric". The aether was believed to exist outside of the three physical dimensions and could be "tapped" for free energy at resonance.

Aetheric energy is said to be limitless, but to vary locally with increases in Earth ,magnetic fields at sunset and sunrise, like the tides of an infinite ocean. This effect is not thoroughly understood, but has been observed in the MRA as increases in output in the early morning and decreases in the early evening. This is still being studied.

Experimentation will determine the optimum MRA design for a specific range of applications.

Vanguard Sciences Note

The use of Lenz Law (back EMF) is legend in free-energy circuits. When the back EMF is reversed and phase-matched to the forward EMF, you have an increase in efficiency because of the reduction of eddy-current heating through the addition of the previously wasted power.

This is generally understood to apply primarily to magnetic flux, yet because frequency is involved, phase-conjugate principles play a major part. Phase conjugation applies to all frequencies regardless of the type of energy being used. Harmony (constructive interference) and dissonance (destructive interference) are controlled using phasing and frequency relationships.

If the rhythmic energy flowing through the mass is made resonant to the mass aggregate resonance, you further reduce the resistance and impedance, thereby achieving unity, and in some cases over unity.

Most people want clean and simple circuits. These would not entail physical motion or large inductive masses as are encountered in orthodox generators. The MRA circuit fits this approach very nicely because it does not involve moving mass, but rather moving energy harmoniously to produce energy.

This file was downloaded from KeelyNet BBS, (214) 324-3501

Any feedback relating to this article should be sent to KeelyNet at P.O. Box 870716, Mesquite, Texas 75187, USA, and also to Nexus Magazine, P.O. Box 30, Mapleton, QLD 4560, Australia.


[ Free Energy ][ Sumeria ]